Oil seal and hexagon socket M6 length 2 cm long Screw required
Also, since Nut stopping Camshaft Chain Cover was about 3 mm long, I put Aluminum 5 mm Washer and adjusted it. Perhaps Oil will leak if it is not Aluminum.
Instead of Oil seal.
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Oil seal and hexagon socket M6 length 2 cm long Screw required
Also, since Nut stopping Camshaft Chain Cover was about 3 mm long, I put Aluminum 5 mm Washer and adjusted it. Perhaps Oil will leak if it is not Aluminum.
Instead of Oil seal.
Rough finishmust consider bracket position. It cause fin broke in by front fender.but cheap price, fine stuff it make forgive all.View Detail
Fits: HONDA MONKEY (Excluding FI), HONDA DAX , HONDA GORILLA , HONDA CUB (Excluding FI)
This is my second purchase. The first one I purchased has no problem except for the Mesh hose that came with it, which I replaced with a commercially available Hose because the finish of the Mesh hose was not good and it was cumbersome to handle.
The thing which was purchased this time tightens Screw of Side cover by hand first, but I felt something caught, but I tried to assemble it for the time being. It is not possible to tighten and loosen. After a while, I tried to tighten the screw because the oil leaked from the side cover, but it was useless. Compared to the OEM side cover, the screw holes are slightly off and the whole thing is distorted, so I had to buy the side cover again. After all, the CoreBody and Bracket are the only ones I can use. It's a shame because the first one I bought is working fine. However, it is still cheaper than the manufacturer's products so you can use it even if it takes some time and effort.
The Engine is CUB series 110cc.
View Detail
Fits: HONDA MONKEY (Excluding FI), HONDA DAX , HONDA GORILLA , HONDA CUB (Excluding FI)
Bad point one.
Instruction Manual is not enclosed. Because it is only an oil cooler, it becomes manageable even if it is not used to it.
Bad point 2.
The oil cooler mountings are welded upside down, or the female screws may have The Bolt didn't go in because it was not chopped.
Others
We are still breaking it in, so we haven't run it at full throttle and its performance is unknown.View Detail
Fits: HONDA MONKEY(except FI)etc.Horizontal TypeEngine , HONDA MONKEYetc.Horizontal TypeEngineUniversal
Hose is hard It's better to get a separate hose
In the case of the BearingCam, it is necessary to scrape off the protruding parts of the ejector If you use it as it is, it is almost certain to leak oil, so you need to prepare a liquid gasket separately It is safe to reassemble the Nipple and then install it
Bottom line, Core was perfectly fine
It can be fixed with a 50mm U-shaped long bolt It's a non-interference, so it's Recommendation
We finally switched to taking out another company..View Detail
Fits: HONDA MONKEY(except FI)etc.Horizontal TypeEngine , HONDA MONKEYetc.Horizontal TypeEngineUniversal
It is in use now, but oil blotting is not improved
We've taken all kinds of measures to install it, but it needs to be checked regularly
The CamBolt is a bit long, so I'm putting the Washer in there, but maybe that's where it came from..
I'm going to try to cut down the bolts and shorten them instead of supporting WasherView Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
обслуговування клієнтів
ЗАМОВЛЕННЯ
ІНФОРМАЦІЯ
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING