Колір: чорний анодований
Найбільший радіус заднього колеса
+ 6см = 225мм
+ 12см = 250мм
+ 16см = 270мм
+ 20см = 305мм
Положення установки задньої підвіски
+ 6см = 245мм
+ 12см / + 16см / + 20см = 310мм
Аксесуари: M12Довговісний вал L = 290мм
Виробнича компанія: KEPSPEED
Країна походження: Китай
* Довгий вал M12 L = 290 мм включений. Вали довжини запасу не можна використовувати.
* Регулятор ланцюга та гачок для підставки в титановому кольорі.
[Установка]
* Цей поворотний кронштейн призначений для використання без регулювання при використанні з повним комплектом.
* Зверніть увагу, що він не підтвердив узгодженість комбінації з продуктами інших компаній, тому, будь ласка, визнайте це.
* Будь ласка, виконуйте монтажні роботи, якщо вони мали досвід технічного обслуговування мотоцикла.
* Кількість рамок приводного ланцюга змінюється залежно від стану автомобіля замовника та передньої та задньої зірочок, тому GM-MOTO не надає інформації щодо цього.
* Не забудьте перевірити, чи є якась ненормальна точка контакту, навіть коли задня підвіска знаходиться в повному нижньому стані.
* Будь ласка, виконайте процедуру зменшення зазору за допомогою шайби, якщо між вашою рамою і цим поворотним важелем є зазор 0,5 мм або більше.
* Це може пошкодити найгірший випадок, якщо шарнірний вал затягнутий при великому зазорі, на поворотному важелі може бути застосовано велике навантаження.
* Існує випадок, коли в детальній частині кожного продукту є незначна зміна специфікації. Є момент, який дещо відрізняється від вступного зображення, але я віддаватиму пріоритет фактичній речі, тому, будь ласка, зрозумійте, будь ласка.
* Ми шукаємо техніка з технічного обслуговування мотоциклів, який би виконував монтажні роботи в спеціалізованому магазині з технічного обслуговування мотоциклів.
* Будь ласка, зверніть увагу на появу так званої "початкової слабкості" після початку пробігу, будь ласка, часто проводьте перевірки, щоб не викликати несподіваних проблем.
* Зображення може містити інші продукти.
* Зверніть увагу, що специфікація продукту може змінитися через причини виробника.
■Color: Black Anodized Aluminum
■Maximum rear wheel radius
+6cm = 225mm
+12cm = 250mm
+16cm = 270mm
+20cm = 305mm
■Rear suspension installation position
+6cm = 245mm
+12cm / +16cm / +20cm = 310mm
■Components: M12 Long Axle Shaft L=290mm
■Manufacturing company: KEPSPEED
■Country of origin: China
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*M12 Long Axle Shaft L = 290mm is included.Stock length axle shafts cannot be used.
*Chain adjuster and stand hook in titanium color.
[About the installation]
*This swingarm is designed to be used without adjustment when the complete kit is used.
※GM-MOTO has not verified the consistency of the combination with other companies' products.
*Please make sure that the person with experience in motorcycle maintenance performs the assembly work.
*The number of tentioners of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
*Even if the rear suspension is at full bottom, make sure to check for any abnormal contact points before riding.
*If the gap between the frame and the swingarm is more than 0.5mm on each side, please use washers to reduce the gap.
*If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.
※There may be some minor specification changes for each product.There may be some points that differ slightly from the introduction image.
*Please have assembly work done in a specialist shop regarding motorcycle maintenance.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
*The image may include other products.
*There may be changes in product specifications due to the manufacturer's reasons.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.