Повний комплект із вкладеною / Шурупи, необхідні для монтажу.
Крім того, кількість: встановити продаж лише обмежена перевага Задня панель прикріплена.
■ Задній перевізник з 4 загальними моделями завершено.
У Yamaha YZF-R25 та YZF-R3, MT-25 та MT-03 є загальний двигун та рама. Композиція кузова автомобіля трохи відрізняється, але вона може бути налаштована на 4 моделі автомобілів.
YZF-R25, який приймає Cowling і дизайн, нагадує SUPER SPORTS 750 і MT-25, що йде за зображенням серії STREETFIGHTER. Обидва автомобілі - це тонкий і чіткий образ та мотоцикл, який є легким важелем та потужним енергоспоживанням.
Задній перевізник - це практичні частини, але я спроектував його якомога більше, щоб не знищити Sharp образ.
■ Створено як можна швидше, забезпечуючи простір пасажира.
Спочатку я спробував задній каркас Frame до SeatLimit, щоб не знищити Тісне зображення з Sharp. Він був розроблений, як я мав намір, але, як я намагався сидіти на Пасажирі, я стиснувся. Це було.
Таким чином, ми розробили його трохи ширше, ніж оригінальний товарний знак, так що навіть хороший чоловік, що сидить на місці пасажира, може собі дозволити, я закінчив його як жорсткий, не жертвуючи комфортом пасажира.
■ Максимальна величина вантажопідйомності 5 кг. Ми підсилюємо кожну частину.
Останнім часом навіть у транспортних засобах, що відображають SUPER SPORTS 750 задній носій і задній коробці Кількість: стає загальним для установки з Set.Large текстури Задня коробка має вагу близько 5 кг, щоб ми посилили кожну частину, так що максимальна велика вантажопідйомність 5 кг.
Місце підкріплення Помістіть підкладку в рамну частину, в якій закріплений задній носій, а також підкладка на ноги тіла.
■ Стиская форма, що підкреслює практичність і дизайн.
Задній бокс Існує можливість того, що кришка буде закрита без дозволу, якщо кришка відкривається горизонтально або кришка відкривається вгорі при відкриванні корпусу заднього носія, так що корпус заднього носія має форму, яка піднімається назад. Це Дизайн з єдності, оскільки він підходить під кутом хвостового капоту.
Установка виконується шляхом видалення Grab Bar з MT-25/03. Незважаючи на те, що потрібно пробурити частину хвостового капота в YZF-R25 / 3, вона розроблена таким чином, щоб свердління капоту було найменшим. Ми також маємо паперовий малюнок так, що положення свердління легко зрозуміти.
Full set with base and screws required for installation.
In addition, the set comes with a limited edition rear box inner.
■The rear carrier for the same four models is available.
Yamaha's YZF-R25 and YZF-R3, MT-25 and MT-03 each share the same engine and frame.Although the vehicle configuration is slightly different, World Walk has developed a rear carrier that can be adjusted to fit four different models.
The YZF-R25 has a cowling and design reminiscent of supersports, while the MT-25 follows the image of a street-fighter.Both bikes have a slim, sharp image and are lightweight with powerful performance.
The rear rack is a practical part, but World Walk designed it not to destroy the sharp image as much as possible.
■Designed to be as sharp as possible while retaining space for the passenger.
In order to keep the sharp and tight image of the bike, the frame of the rear rack was brought up to the very edge of the seat.The design of the vehicle is as World Walk wanted, but it is too tight for the passenger to sit on.
The passenger seat was designed to be slightly wider than the first sample to allow room for a larger man to sit in the passenger seat.It is a tight fit without sacrificing passenger comfort.
■Maximum loading capacity is 5kg.World Walk is reinforcing every part of it.
Recently, it has become common to install a rear carrier and a rear box as a set, even for super sports inspired vehicles.Some of the larger rear boxes weigh about 5kg, so I reinforced each part of the box and set the maximum load capacity to 5kg.
The reinforcement plate is placed on the frame where the rear carrier is installed, and also on the legs of the main body.
■The shape of the buttocks is designed for practicality and design.
When the rear box is installed, the lid may close by itself if it is horizontal or raised forward when the lid is opened.This is why the rear rack is designed to be raised backwards.The angle of the tail cowl is the same as the angle of the tail cowl, so the design has a sense of unity.
To install, remove the grab bar from MT-25 / 03.YZF-R25 / 3 requires drilling of some parts of the tail cowl, but World Walk has designed the cowl so that drilling of the cowl is minimized.A paper pattern is also included to help you know where to drill the holes.